SPECIFICATIONS    

                                Low Band                       High Band

I/P frequency range : 10.7~11.7GHz                11.7~12.75GHz
L.O. frequency : 9.75GHz                               10.60GHz
O/P frequency range : 950 ~1950MHz              1100 ~2150MHz

L.O. stability : +/-3MHz (-30°C~+60°C)
L.O. phase noise : <-50 dBc @ 1KHz offset
<-80 dBc @ 10KHz offset
<-95 dBc @ 100KHz offset
Noise figure @ 25°C : 0.8dB (Typ.) 0.8dB (Typ.)
Cross-pol Isolation : 25dB (Typ.)
Image rejection : 40dB (Min.)
Output VSWR : <2.5:1
Conversion gain : 50~60dB
Gain flatness : +/-0.5dB/26MHz, 8dB over each IF band
Output spurious : <-60dBm
Current consumption : 120mA (150mA Max.)
Low/High band switching : Low band: 0KHz
High band: 22KHz +/-4KHz
Polarity switching voltage : Vertical: 10.5 - 14.0V
Horizontal: 16.0 - 20.0V
Reflector type : Optimized for offset feed dish with F/D: 0.45 ~ 0.7
Working temp/humidity : -30°C~+60°C/0 ~100%
Output connector : 75 OHM

 Input freq. range:

Low band: 10.70 to 11.80GHz

High band: 11.70 to 12.75GHz

 L.o. frequency:

Low band: 9.75GHz (1MHz @ 25℃)

High band: 10.60GHz (1MHz @ 25℃)

 L.o. stability:

Low band: 2MHz (-40℃ to +70℃)

High band: 2MHz (-40℃ to +70℃)

 Output freq. range:

Low band: 950 to 2050MHz

High band: 1100 to 2150MHz

 Control signals:

Low band: Ca or Cb (see below)

High band: Ca,Cb or Cc(Cc: continuous 22KHz)

 Noise figure: 0.7dB typ.

 Conversion gain: 55dB typ.

 Input VSWR: 2.5:1

 Output VSWR: 2.0:1 (max.)

 Output connector: F-female connector

 Output impedance: 75 ohms typ.

 Cross polar isolation: 20dB (min.)

 Image rejection: 45dB

 Phase noise:

-50dBc @ 1KHz

-75dBc @ 10KHz

-95dBc @ 100KHz

 Supply voltage:

Ca: 11.5 to 14.0V (vertical polarization),13 VDC typ.

Cb: 16.0 to 19.0V (horizontal polarization),18 VDC typ.

 Operating temperature: -40℃ to +70℃

 Storage temperature: -40℃ to +80℃

 Relative humidity: 0% to 95%

 Size: 115mm x 60mm x 60mm

 Weight: 105g

Ku-Band LNB HITOPSAT L728

Features:

DVB-S PCI

- Quality digital satellite (DVB-S) channel reception
- Pure USB 2.0 High speed interface
- Compact and economic
- DVB data service
- Instant recording -- Record digitally as MPEG II format
- Schedule recording -- Set your own recording list and playback
- Time-shifting -- Pause live TV shows and never miss any marvelous moment!
- IP MEPG4 Reception and recording
- Support third party software: Mytheatre Progdvb DVBDream AltDVB
- Electronic program guide
- Support DiSEqC1.2 & USALS
- Multi-language output
- MPEG II software decoding

Protocol Supports
- Compatible with DVB Standard
- Supports MPEG2 Video/Audio/AC3 stream
DVB-S PCI signal Switch Supports
- 22KHz tone device
- DiSEqC2.0 switch
- DiSEqC1.2 motor
- DiSEqC1.1 switch
- Tone Burst device

OS Supports
- Windows 2000 SP4, with DirectX 8.1 or above
- Windows XP SP2, with DirectX 8.1 or above

PC requirements
- 500MHz CPU or above
- 8M Bytes RAM or above
- 128M Bytes RAM or above
- 50M Bytes hard disk free space

Hardware Features
- Interface
-- Signal connector without loop through
-- LNB Voltage: 13V/18V, 300mA max
Tuner
- Sharp 0194
-- Receiving frequency coverage: 950 ~ 2150MHz
-- Input level: -65dBm ~ -25dBm
-- Input structure: F type female
-- Nominal input impedance: 75 ohm
-- Channel selection system: PLL synthesizer (Clock 4.0MHz)
-- Step frequency: 500KHz
-- Symbol Rate: 2 ~ 45Msps
-- FEC
--- Inner decoder: Viterbi soft decoder, Constraint length M=7
--- Punctured codes 1/2, 2/3, 3/4, 5/6, 7/8
--- Outer decoder: Reed-solomon decoder, for 16 parity bytes
--- Block lengths 204 bytes or 188 bytes

Software Functions Overview
- Digital TV or Radio playing
- Recording and Pre-Set recording schedule
- Recording file playback
- Time-Shifting
- Still Picture Capture
- Preview
- Support HDTV

Card Reader for 4000/ 5000/ 6000, STRONG SRT4620II,SRT4650 satellite receiver Easy 1 plug installation. Facilitates the use of conditional access cards in your 4000, 5000 ,6000 ,SRT4620II and SRT4650 Receiver.

• Frequency Range 1.8MHz~65MHz

• Accuracy: <12%

• Maximum input power: 600Watts

4 way ( 4x1 ) DiSEqC switch. Connect up to four satellite dishes to one receiver. Compatible with most Free To Air receivers including Pansat 2500A, 2700A, 3500S, 3500SD, 5000HC, 6000HXC, Fortec Star Lifetime Ultra, Cool Sat 4000 Pro, Coolsat 5000 Platinum, Viewsat vs2000 Platinum, View Sat vs 2000 extreme xtreme, Digiwave DG7000 and many more.

The DiSEqC switch will enable the user to select one LNB signal between 4 different LNBs of any type. The 4 input ports marked SAT1, SAT2, SAT3 or SAT4 are connected to the 4 LNBs, which may be on 4 different dishes, and the output marked OUT is connected to the receiver. The selection of the LNBs is done by choosing the appropriate Tone Burst A, B, C, or D in the menu of the receiver

RS232 Cable (Pc TO Receiver),This is a straight thru 9 pin serial cable used to connect your computer to your FTA satellite receiver for programming / updating the software / firmware of your FTA receiver. Works with Pansat 2500a,Coolsat5000.

KU band satellite dish Size: 45cm, 60cm, 75cm, 90cm, 120cm

Description:

Now you no longer need to boot up your notebook PC just to find out whether you are near a Hot Spot! IOGEAR's little WiFi HotSpots Explorer is an RF wireless device that detects WiFi 802.11b and 802.11b/g signals. It can capture WiFi signals while avoiding interference from other devices such as 2.4GHz cordless telephones, A/V senders, microwave ovens and Bluetooth devices. Just turn it on and get online without the hassles!

Features: